Custom Doors and Frames

Before and after custom walk-in freezer door and frame

Custom walk-in cooler doors and frames

Off-the-shelf walk-in doors assume a standard opening. A lot of Southern California kitchens do not have one. Left Coast Refrigeration builds custom doors and jambs to the opening we measure — cooler or freezer — then installs them ourselves.

Every door we build comes standard with diamond plate kickplates inside and out, and with hardware. That is not an upgrade package. Kitchens kick doors. Carts hit doors. If the bottom of the slab is thin metal, it will look like it in a year.

Work is done from the Escondido shop. We have been on this kind of job since 2013: restaurants, grocery, bars, and other food businesses that need a door that closes, seals, and survives the line.

Custom walk-in cooler door with alumafoam and custom-cut diamond plate kick section, built by Left Coast Refrigeration in Escondido
Custom walk-in door: alumafoam skin with a custom-cut diamond plate kick section where it takes the hits.

Recent shop work: a custom walk-in cooler door with an alumafoam skin and a custom-cut diamond plate section across the bottom of the slab — diamond plate where it takes the hits from carts, boots, and cases. Built in Escondido and cut to this door, not pulled off a shelf.

What is included

  • Custom door and jamb sized to the opening
  • Diamond plate kickplates, inside and out
  • Hardware (hinges, handles, door closers as required)
  • Install by Left Coast Refrigeration
  • Custom gasket made in-house to the new door

We also replace hardware on existing doors when the slab is still good: hinges, handles, closers. If the door is delaminated, the window is shot, or the frame is bent, replacing hardware is wasting money. We will say so.

Heater wires in freezer door frames keep frost off the seal and threshold. If the door is freezing shut or the gasket is tearing on ice, that is part of the conversation.

Who this is for

  • Walk-ins with original doors that no longer square up
  • Odd-sized openings from old boxes, add-ons, or remodel leftovers
  • Freezer doors that will not close or that leak at the corners
  • High-traffic doors that have had the bottom kicked through
  • Kitchens replacing a door as part of a box refurb

A door job is often what keeps a walk-in in service. The box can be fine. The opening is not.

Why the door is usually the problem

Cold loss at the door is visible: frost, a wet floor, a gasket hanging off, a closer that does not latch. Staff prop the door. The compressor never rests. Product at the front of the box sits warm.

A custom door does not fix a ruined floor or dead insulation. It does fix the opening. Combined with a gasket that matches and a frame that is actually square, it is one of the highest-leverage repairs on a commercial walk-in.

We do not promise a number off the energy bill. A door that latches and seals wastes less energy than one that does not. If you want the envelope addressed too, look at alumafoam refurbishment and walk-in floors.

Diamond plate on the kick and on high-abuse walls is the same idea as a proper door: the box gets hit every day. Custom metal work covers plate and other fabrication when you are not replacing the whole door.

How to start

Call 760-745-5252, Monday–Friday, 8AM–4PM PST. Send opening measurements and photos through the estimate form if you have them. We inspect for free when the job needs it.

Left Coast Refrigeration
1175 Industrial Ave, Suite J, Escondido, CA 92029
info@leftcoastrefrigeration.com

Service area · All services

Face frame, plug frame, and surface-mount doors

National door sellers talk about face frame, plug / retrofit frame, and surface-mount replacement doors. In plain shop language: some jobs replace the door slab into an existing jamb, some rebuild the jamb (prehung door and frame), and some surface-mount a new door assembly over a worn opening so you can replace the door without replacing the whole box. We measure the opening and tell you which approach fits — odd sizes and remodel leftovers are normal for us.

Exact-fit measurement (built to the opening)

Custom walk-in cooler and freezer doors are built to the opening we measure — not forced from a stock WxH chart. We take width and height carefully (to about 1/8″ where the opening allows) so the slab squares, the cam-lift hinges land, and the magnetic gasket seats. That is how you get a door that latches instead of a “close enough” mail-order unit that never seals.

Hardware on every door we hang — handles, hinges, closers, inside safety releases — is covered in detail on our walk-in cooler door hardware page. Gaskets for the new door are made in-house: custom gaskets.

Scroll to Top